Bespoke staircases in Hebden Bridge
Bespoke timber staircases set out from a site survey, manufactured in our workshop and installed by our own fitters. Covering Hebden Bridge and the wider West Yorkshire area.
- Made to size from a measured survey, never cut down from stock
- FSC-certified timber with chain-of-custody paperwork
- Fixed written quotation with the lead time stated
- 10-year workmanship guarantee in writing
Free measured survey · No obligation · Reply within one working day
Quote for Hebden Bridge
Free measured survey in Hebden Bridge.
Bespoke staircases in Hebden Bridge
Nothing about Open Riser Staircases in Hebden Bridge is settled until someone has been on site. Property here runs to millstone grit terraces, weavers' cottages and Victorian civic frontages, and each of those brings its own set of dimensions. With Pennine exposure with hard frost and horizontal rain in the mix, frost damage at end grain and blown joints on exposed hillside stock is a question of when rather than whether. The detail we will not compromise on is open treads that still satisfy the 100mm sphere rule under Part K.
Every job is measured on site first, because drawn sizes and built sizes are seldom the same. Tell us what you are working with and we will put a fixed figure in writing.
Bear in mind for this area: gritstone reveals hold water against frames, so drainage detail is critical.
What we cover locally
- Bespoke Staircases in Hebden Bridge
- Cut String Staircases in Hebden Bridge
- Open Riser Staircases in Hebden Bridge
- Cantilever Staircases in Hebden Bridge
Survey visits in Hebden Bridge are usually booked within a week. There is no charge for the survey and no obligation to proceed.
Made to size for Hebden Bridge
Every item below is manufactured to your dimensions.
Bespoke Staircases
Designed and set out from your actual floor-to-floor height.
Learn more →Cut String Staircases
Open-sided stairs with the treads exposed at the string.
Learn more →Open Riser Staircases
Contemporary open-tread stairs meeting Part K.
Learn more →Cantilever Staircases
Floating treads with concealed structural support.
Learn more →Staircase Renovation
Re-treading, re-balustrading and squeak elimination.
Learn more →Handrails and Balustrades
Continuous handrails, volutes, spindles and newel posts.
Learn more →Loft Conversion Stairs
Space-saving flights for tight loft openings.
Learn more →Staircase Parts
Newels, spindles, strings and treads supplied loose.
Learn more →Rise, going and headroom in Hebden Bridge
Three numbers decide whether a staircase is comfortable or awkward, and they are the first things we measure.
Rise
Maximum 220mm per step for a private stair under Part K. Consistent to within 5mm across the whole flight, because the foot notices what the eye does not.
Going
Minimum 220mm. Rise and going together must satisfy the pitch rule, which is why a flight cannot simply be shortened to fit a smaller opening.
Headroom
2m measured vertically from the pitch line. This is the constraint that most often forces a winder instead of a straight flight.
What clients tell us
Feedback collected directly from completed projects. Full written references are available on request before you commit.
“The headroom was tight and they redesigned the winder rather than telling us it could not be done.”
Verified client, West Yorkshire“Dry-assembled in the workshop first, so installation day was genuinely uneventful.”
Verified client, West Yorkshire“No squeaks at all a year on, which was the whole reason we replaced the old one.”
Verified client, West YorkshireHebden Bridge questions
What guarantee do you provide?
Ten years on workmanship, covering manufacture and the factory-applied finish. Where we install, the installation is covered too. It is issued in writing with the handover paperwork.
Can you match an existing profile?
Yes. If you can supply a section, a photograph with a rule in shot, or an old unit, we can replicate the profile. For conservation work this is usually the condition the planning officer will apply.
What if the opening is out of square?
Most older openings are. The survey records the actual dimensions at several points and the unit is manufactured to suit, which is the main reason we survey rather than work from the sizes given over the phone.
Will the finish need maintaining?
A factory-applied microporous finish typically needs inspection every three to five years, sooner on exposed coastal elevations. Maintaining it is far cheaper than letting a coating fail and the timber take up water.
Do you take a deposit?
Not before the measured survey. A deposit is only requested once the survey is complete and you have approved the final schedule and price.
Talk to us about your project
Free, no obligation, and a fixed figure in writing. We will tell you honestly if what you are asking for is not the right answer.
Request a quote Call 0800 088 6248